{"id":2279,"date":"2023-06-08T18:10:49","date_gmt":"2023-06-08T17:10:49","guid":{"rendered":"https:\/\/m0aws.co.uk\/?p=2279"},"modified":"2023-06-08T22:19:56","modified_gmt":"2023-06-08T21:19:56","slug":"replacement-for-the-funcube-dongle-pro","status":"publish","type":"post","link":"https:\/\/m0aws.co.uk\/?p=2279","title":{"rendered":"Replacement for the Funcube Dongle Pro+"},"content":{"rendered":"\n

For some time now I’ve been using my Funcube Dongle Pro+<\/a> (FCD) as my QO-100<\/a> downlink receiver. It’s worked fairly well and has given me the ability to listen to stations on the satellite over the last few months.<\/p>\n\n\n\n

During this time I have noticed a couple of things about the FCD that has lead me to the final decision to change to a new SDR<\/a> device.<\/p>\n\n\n\n

The first of these ‘things’ is the fact that the FCD gets seriously overloaded when there are multiple large SSB signals within the receive pass band. The only way to manage this is to constantly keep changing the software based AGC, mix and LNA settings to reduce the levels of the incoming signals so that the overloading stops. This is great except when you tune to a quiet part of the satellite transponder you have to turn all the settings back up again to be able to hear the weaker signals. After a while this becomes tiresome.<\/p>\n\n\n\n

The fact that there isn’t a hardware AGC in the FCD is a major drawback when being used for satellite reception especially when it’s on the end of a very high gain LNB<\/a> and dish antenna<\/a>.<\/p>\n\n\n\n

The second of these ‘things’ is the fact that I can’t see the whole transponder<\/a> bandwidth at one time with the FCD as it has a very small receive bandwidth capability. This means that I am constantly tuning up and down the transponder to see if there are any stations further up or down in frequency.<\/p>\n\n\n\n

\"Funcube
Funcube Dongle Pro+<\/figcaption><\/figure>\n\n\n\n

Talking to more experienced satellite operators in the Matrix Amateur Radio Satellites room <\/a>they recommended replacing the FCD with a NooElec NESDR SMArt v5<\/a> that has hardware AGC and is capable of receiving and displaying a much wider bandwidth.<\/p>\n\n\n\n

Looking on Amazon<\/a> the NooElec NESDR SMArt v5 is only \u00a333 so I decided to place an order for one and give it try.<\/p>\n\n\n\n

In typical Amazon style the SDR receiver arrived the next day and I wasted no time getting it plugged in and connected to the QO-100 ground station.<\/p>\n\n\n\n

The NESDR SMArt v5 is based on the well known RTL-SDR<\/a> that came onto the market some time back but, has a number of improvements in it that take it to the next level.<\/p>\n\n\n\n

The first thing that I was happy with was the fact that the GQRX SDR software<\/a> I use recognised it immediately on startup, no configuration or drivers were required it just worked, straight out of the box. Since I use Kubuntu Linux<\/a> on my radio room PC I did wonder if I would need to get into installing extra libraries etc but, thankfully none of that was required.<\/p>\n\n\n\n

Looking at the signals from the QO-100 satellite initially they appeared to be nowhere near as strong as they were on with the FCD. Looking at the settings in GQRX I noticed that the hardware AGC was off and the LNA setting was back to it’s default very low level.<\/p>\n\n\n\n

I switched on the AGC and then increased the LNA setting to 38.4dB and found that the signals were now plenty strong enough on the display but, not overloading the receiver.<\/p>\n\n\n\n

I then went on to adjust the display so that I could see the whole satellite transponder bandwidth on the screen. This is great as it enables me to see the low, middle and high beacons that mark out the narrow band section of the transponder and at a glance see all the stations using the satellite. This was a massive improvement in itself and one that I am very pleased with.<\/p>\n\n\n\n

\n
\"NooElec
NooElec v5 SDR<\/figcaption><\/figure>\n\n\n\n
\"NooElec
NooElec v5 SDR<\/figcaption><\/figure>\n<\/figure>\n\n\n\n

Using the NooElec NESDR SMArt v5 SDR it very soon became clear that it copes with multiple large signals in the pass band so much better than the FCD did. There’s no more overloading of the receiver, no more ghost signals appearing on the waterfall due to the front end not being able to cope and no more having to constantly keep playing with the settings to get things under control. The hardware AGC built into the SDR device does a great job at keeping it all under control whilst receiving a much wider bandwidth than the FCD ever could. <\/p>\n\n\n\n

The satellite beacons are now received at S9+15dB without the receiver being overloaded, the first time I have seen this since starting out on my QO-100 venture.<\/p>\n\n\n\n

The other thing that became obvious very quickly is that frequency stability is much better than it was with the FCD, it doesn’t drift up and down the transponder now and stays tuned exactly where I put it. It’s also on frequency whereas, the FCD was always 1.7Khz off frequency.<\/p>\n\n\n\n

\"GQRX<\/a>
GQRX showing QO-100 Transponder signals<\/figcaption><\/figure>\n\n\n\n

The NooElec NESDR SMArt v5 is very well put together, it has an aluminium case that acts as a heatsink (it does get warm!) and overall the build quality is much better than the plastic cased FCD. When I think that I paid close to \u00a3100 for the FCD and the NooElec NESDR SMArt v5 only cost \u00a333, I am amazed at the build quality.<\/p>\n\n\n\n

Overall I’m extremely pleased with the purchase of the new SDR, it slotted in perfectly as a replacement for the FCD, works great with GQRX, my QO-100 Node Red Dashboard and performs considerably better than the FCD. Overall money well spent!<\/p>\n\n\n\n

You can find the NooElec NESDR SMArt v5 spec sheet here<\/a>.<\/p>\n\n\n\n

More soon …<\/p>\n","protected":false},"excerpt":{"rendered":"

For some time now I’ve been using my Funcube Dongle Pro+ (FCD) as my QO-100 downlink receiver. It’s worked fairly well and has given me the ability to listen to stations on the satellite over the last few months. During this time I have noticed a couple of things about the FCD that has lead … <\/p>\n

Continue reading “Replacement for the Funcube Dongle Pro+”<\/span><\/a><\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[173,177,180,163,176,166,165,169,4,171,172,223,222,135,134,167,123,168,5,144,110,215,17],"tags":[],"class_list":["post-2279","post","type-post","status-publish","format-standard","hentry","category-10ghz","category-bullseyelnb","category-dashboard","category-devices","category-dishantenna","category-fcd","category-funcube-dongle","category-gqrx-sdr","category-ham-radio","category-kubuntu","category-lnb","category-nesdr-smart","category-nooelec","category-opensource","category-projects","category-qo-100","category-radio-shack","category-satellite","category-sdr","category-shf","category-station","category-ubuntu","category-weak-signals"],"_links":{"self":[{"href":"https:\/\/m0aws.co.uk\/index.php?rest_route=\/wp\/v2\/posts\/2279","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/m0aws.co.uk\/index.php?rest_route=\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/m0aws.co.uk\/index.php?rest_route=\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/m0aws.co.uk\/index.php?rest_route=\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/m0aws.co.uk\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=2279"}],"version-history":[{"count":22,"href":"https:\/\/m0aws.co.uk\/index.php?rest_route=\/wp\/v2\/posts\/2279\/revisions"}],"predecessor-version":[{"id":2305,"href":"https:\/\/m0aws.co.uk\/index.php?rest_route=\/wp\/v2\/posts\/2279\/revisions\/2305"}],"wp:attachment":[{"href":"https:\/\/m0aws.co.uk\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=2279"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/m0aws.co.uk\/index.php?rest_route=%2Fwp%2Fv2%2Fcategories&post=2279"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/m0aws.co.uk\/index.php?rest_route=%2Fwp%2Fv2%2Ftags&post=2279"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}