Not having a Pluto+ myself I’ve never actually played with one before and so this was new and exciting. I have, however played with Steve’s LibreSDR which is a later iteration of the Pluto+ and so, I had an idea of what I was getting into.<\/p>\n\n\n\n
Firstly, how do you know when you have bricked your Pluto+? <\/p>\n\n\n\n
Fortunately the Pluto+ device is actually quite clever and will inform you when it is bricked. The first sign you will notice is that you can no longer connect to the device using a USB connection to the data socket. The second sign is that when you take the top off the case you’ll notice that the blue LED is off and the green LED is on constantly. These are both classic signs that the device is bricked and needs rescuing<\/p>\n\n\n\n
So, how do we rescue a bricked Pluto+?<\/p>\n\n\n\n
Firstly, disconnect all cables and power to the device, it needs to be in a powered down state. Next remove the top of the case completely.<\/p>\n\n\n\n
Unlike the LibreSDR the Pluto+ doesn’t boot from SD card so, we have to tell it that we want to boot it from an SD card. This is done by shorting the 3v3<\/em><\/strong> and SD-H<\/em><\/strong> pins together using a jumper as shown in the photo below. (Black Jumper)<\/p>\n\n\n\n I believe that the v1 version of the Pluto+ has 1.8v instead of 3.3v, if this is the case on your device just short the SD-H pin to the 1v8 pin instead.<\/p>\n\n\n\n Next we need to make sure that the URST<\/em><\/strong> pin is connected to the MIO46<\/em><\/strong> pin as shown by the green<\/em><\/strong> jumper in the image above. I put the jumper into this position as I am going to be using firmware that has ethernet support built in. If you want to load the official firmware then you will need to connect the URST pin to the MIO52 pin instead.<\/p>\n\n\n\n Next we need to load the new firmware onto an appropriate SD card. I’m using the F5OEO<\/a> firmware that has ethernet support with DHCP built in. You can get the firmware from this Github link<\/a>.<\/p>\n\n\n\n Whilst the firmware is downloading, insert your SD card into your PC and format it using a FAT32 filesystem. <\/p>\n\n\n\n Once the firmware has downloaded, unzip the file and save the contents of the zip file to a directory. Using your favourite file manager or in the case of a Linux junkie like me, the command line, copy the contents of the sdimg<\/em><\/strong> folder into the root of the SD card.<\/p>\n\n\n\n Note: That’s copy of the contents<\/em><\/strong> of the sdimg<\/em><\/strong> folder, not the folder itself.<\/p>\n\n\n\n Make sure to eject your SD card safely before removing it from your PC to ensure you don’t corrupt the contents.<\/p>\n\n\n\n Insert the SD card into the Pluto+ (it’s still powered down at this point with the top off).<\/p>\n\n\n\n Plug the USB A end of the USB cable into your PC but, do not<\/em><\/strong> plug the micro USB end into the Pluto+ just yet!<\/p>\n\n\n\n Now this is the tricky part, you need to hold down the DFU Button<\/em><\/strong> on the Pluto+ PCB (It’s behind the professor image on the PCB) whilst inserting the micro-USB plug into the DATA<\/em><\/strong> port of the Pluto+.<\/p>\n\n\n\n Once you see that the green and blue LED lights come on permanently, let go of the DFU Button<\/em><\/strong> and let the Pluto+ boot from the SD card. A short while afterwards the green LED should start flashing, this means your Pluto+ is alive again and has booted from the SD card.<\/p>\n\n\n\n At this point it’s important not<\/em><\/strong> to unplug the USB cable and not<\/em><\/strong> to remove the SD card from the device, we’re only half way there!<\/p>\n\n\n\n After a little more time the Pluto+ will appear in your file manager as a drive called PlutoSDR<\/em><\/strong>, navigate to this drive using your favourite file manager.<\/p>\n\n\n\n At the same time, open another window in your file manager and navigate to the folder where you saved the files from the Zip file. In this directory you will see the following two files:<\/p>\n\n\n\n Copy these two files from the directory where you saved them into the root of the PlutoSDR<\/em><\/strong> drive.<\/p>\n\n\n\n Once this is complete, eject the PlutoSDR<\/em><\/strong> drive safely. <\/p>\n\n\n\n The green LED will now start blinking, don’t do anything, just leave everything as it is and the device will now create a new boot image on it’s own built in storage.<\/p>\n\n\n\n This process will take about 5mins so, go grab a cold beer, glass of wine or anything else that takes your fancy, sit back and relax.<\/p>\n\n\n\n Eventually the green LED will stop flashing, wait another minute or so for the process to fully complete.<\/p>\n\n\n\n If the PlutoSDR<\/strong> drive has reappeared in your file manager, safely remove the drive from your file manager and unplug the micro USB connector from the Pluto+ powering it down.<\/p>\n\n\n\n It’s now important to remove<\/em><\/strong> the 3v3<\/em><\/strong> to SD-H<\/em><\/strong> jumper as we no longer need to boot from SD card.<\/p>\n\n\n\n You can now refit the top cover and the 4 screws and put the case back together. Connect an ethernet cable and micro USB cable to the DATA port and wait.<\/p>\n\n\n\n After about 10-15 seconds the green LED should flash and your Pluto+ is now no longer bricked and ready for use once more.<\/p>\n\n\n\n You can SSH to your Pluto+ using the normal Linux SSH command logging in as root<\/em><\/strong> with a password of analog<\/em><\/strong>.<\/p>\n\n\n\n![\"Pluto+](\"https:\/\/m0aws.co.uk\/wp-content\/uploads\/2025\/06\/Pluto-Plus-SDcard-Boot-Jumper.jpeg\")
<\/a>boot.frm\npluto.frm<\/code><\/pre>\n\n\n\n
![\"Steve's](\"https:\/\/m0aws.co.uk\/wp-content\/uploads\/2025\/06\/Steves-Unbricked-Pluto-Plus.png\")